Working hours:Mon - Sat 9:00 AM - 8:00 PM Call Us: +91 7984353863

Our Products

Capitalise on low hanging fruit to identify a ballpark value added activity to beta test, override the digital divide with additional clickthroughs from DevOps, nanotechnology.

portfolio_03

We are a well-known producer, exporter, and supplier of Extension Pieces of the highest quality, which are utilized in the pipe installation sector.

Read More

portfolio_03

A hex nipple is a fitting made from a length of pipe with a hexagonal part in the center that a pipe wrench can fit onto and be used to tighten or loosen.

Read More

portfolio_03

Adapter for the Brass Union, Male Brass A brass threaded piece on the opposite end of a threaded fitting can be screwed into the female end of another fitting or appliance. Threaded fittings are a hybrid joint with a union on one end that can be linked to a pipe. technical specifics.

Read More

portfolio_03

Reducing bushes are made so that they can be solvent-cement into the socket of another fitting to shrink the pipe. They are frequently employed in manifolds and other structures where smaller pipes are detached from bigger ring mains or spurs.

Read More

portfolio_03

In pipeline and plumbing, a coupling (or coupler) is a very short piece of pipe or tube having a socket at one or both ends that enables two pipes or tubes to be linked, welded (steel), brazed (brass), or soldered (copper, brass, etc.) together.

Read More

portfolio_03

The Surrey flange or Danzey flange, York flange, Sussex flange, and Essex flange are common flanges used in plumbing. The hot water tank's top is fitted with Surrey and York flanges, which enable all of the water to be removed without causing any damage to the tank. To provide a uniform flow of water to showers, they are frequently employed. Drilling a hole into the tank's side is necessary for an Essex flange.

Read More

portfolio_03

Brass threaded fittings known as tank connectors are used as feed-throughs to supply water to tanks and other vessels. A brass fitting known as a straight tank connection is typically used to pass through the wall of a water tank.

Read More

portfolio_03

The brass meter coupling is a pipe fitting that's typically used to join a water meter installation, but it can also be used to join other threaded-connection accessories or network components.

Read More

portfolio_03

A fitting with a T shape is known as a pipe tee fitting. It features one primary connecting line, two outlets, each at a 90-degree angle. It is a pipe that is used to join pipes at a 90° angle and has nearby outputs.

Read More

portfolio_03

Elbows: Used to alter the pipe run's angle or direction. more frequently in 45- and 90-degree turns. The fitting's sweep indicates how quickly a transition or direction change is made.

Read More

portfolio_03

A little section of brass tubing with threads on both sides is known as a brass nipple. They are typically used to join a pipe to a valve, tool, or other pipes. Although it is frequently used in plumbing, brass is also used in the vehicle industry. There, it is utilized in gasoline lines, hose ends, and air brake systems.

Read More

portfolio_03

The ends of many hydraulic or pneumatic pipes or tubes are sealed using pipe plugs. Plugs are crucial parts of the plumbing system for both household and commercial water supply lines, machines, etc.

Read More

portfolio_03

A brass pipe fitting known as a brass socket (female-female) is used to unite two straight sections in pipes of the same diameter. It has an internal female thread on both ends of a hollow cylindrical body.

Read More

portfolio_03

They are used to fasten and secure hoses and the pipe that goes with them.

Read More

portfolio_03

A short section of threaded brass pipe is known as a brass nipple. Often, they are utilized to join a pipe to a valve, device, or other pipes. Brass is utilized extensively in the plumbing industry, but it is also employed in the automobile sector.

Read More

portfolio_03

Common nuts used with bolts, set screws, studs, threaded rods, and any other fastener with machine screw threads are known as brass hexagon nuts. These nuts are mostly utilized in machinery and equipment.

Read More

portfolio_03

Copper fittings are known as essential spare parts for HVAC systems since they are soldered to connect with a copper tube or other fittings. The usage of copper fittings is also common in sectors including plumbing, solar power, shipbuilding, medical gas delivery, and others.

Read More

portfolio_03

This CPVC fitting controls the flow of hot and cold water across vertical junctions throughout the plumbing system. The cross tee can be utilized with a range of pipes with various diameters and pressure-carrying capacities.

Read More

portfolio_03

A fitting formed from a length of pipe with a hexagonal section in the center that a pipe wrench can fit onto and be used to tighten or loosen is known as a chrome-plated nipple.

Read More

portfolio_03

Elbows: Used to change the angle or direction of the pipe run. more often at turns of 45 and 90 degrees. How swiftly a transition or direction change is made is indicated by the fitting's sweep.

Read More

portfolio_03

A CP pipe fitting known as a brass socket (female-female) is used to unite two straight sections in pipes of the same diameter. It has an internal female thread on both ends of a hollow cylindrical body.

Read More

portfolio_03

A waste coupling is a connection used to join the drain system to the waste pipe coming from a sink, basin, or other fixture. Waste connections may appear to be a little, unimportant component, yet they are essential to the correct operation of the entire plumbing system.

Read More

portfolio_03

Pipe plugs are used to seal the ends of numerous hydraulic and pneumatic pipes and tubes. Plugs are essential components of the plumbing system for water supply lines, equipment, etc. in both residential and commercial settings.

Read More

portfolio_03

Galvanic nickel-plated brass is used to make brass cable glands. They offer a higher resistance to corrosion and many forms of mechanical and strain-related burdening, making them stronger than plastic cable glands.

Read More

portfolio_03

Similar to the cable glands in ordinary plugs, earth tags offer an earth-bond attachment for cable glands. Everyone coming into contact with the cable gland is kept safe from injury when a fault occurs because of the earth tag, which securely directs the energy toward the ground.

Read More

portfolio_03

One method to stop vibration from losing a bolted joint is to use locknuts. Safety wire, lock washers, and thread-locking fluid are further techniques.

Read More

portfolio_03

Stopping Plugs offer a way to block off inactive ports on equipment allowed for operation in hazardous environments while still preserving the installation's integrity and Ex approval.

Read More

portfolio_03

Brass connectors, reducers, and adaptors. Eccentric reducers are occasionally employed to maintain the top or bottom of the pipe level; reducers are often concentric.

Read More

portfolio_03

Split bolt connectors are made to attach two or more wires together, much like all connections. They'll make it possible for electricity to move from one wire to the others.

Read More

portfolio_03

This selection of split bolts is composed of a high-conductivity copper alloy with a captive saddle that evenly presses conductors.

Read More

portfolio_03

Galvanic nickel-plated brass is used to make brass cable glands. They offer a higher resistance to corrosion and many forms of mechanical and strain-related burdening, making them stronger than plastic cable glands.

Read More

portfolio_03

Similar to the cable glands in ordinary plugs, earth tags offer an earth-bond attachment for cable glands. Everyone coming into contact with the cable gland is kept safe from injury when a fault occurs because of the earth tag, which securely directs the energy toward the ground.

Read More

portfolio_03

One method to stop vibration from losing a bolted joint is to use locknuts. Safety wire, lock washers, and thread-locking fluid are further techniques.

Read More

portfolio_03

Stopping Plugs offer a way to block off inactive ports on equipment allowed for operation in hazardous environments while still preserving the installation's integrity and Ex approval.

Read More

portfolio_03

Brass connectors, reducers, and adaptors. Eccentric reducers are occasionally employed to maintain the top or bottom of the pipe level; reducers are often concentric.

Read More

portfolio_03

Split bolt connectors are made to attach two or more wires together, much like all connections. They'll make it possible for electricity to move from one wire to the others. SPLIT BOLT CONNECTOR WITH ROUND HEAD

Read More

portfolio_03

This selection of split bolts is composed of a high-conductivity copper alloy with a captive saddle that evenly presses conductors.

Read More

Jamnagar

Headquarters

Plot No. 3021, Phase-III, Dared - GIDC, Jamnagar - 361004.
+ 91 7984353863

www.pantherexim.com

info@pantherexim.com

GET IN TOUCH

Follow Our Activity

Interactively coordinate proactive e-commerce via process-centric “outside the box“ thinking.